Search results

a used weber progressive 32/36 DFAV with manifold and filter . came of a running 1600 van that was converted to a bigger twin carb engine. £100 a used pair of dellorto drla40's came of an alfa 33. £200 a used pair of weber ICH's the same as ICT's need rebuilt kits £70 a used crane...

http://www.volkszone.com/VZi/showthread.php?t=936306 not my advert nor do I know the seller but these could be a bargain , for someone wanting power next year , these are nearly new going by the description. the seller is now open to offers . linkage kit worth £60 second hand manifolds worth...

solid 1967 beetle on uk plates with:- roll cage centreline alloys disk brakes flip front harnesses 1835cc engine twin 40's, 120cam, balanced bottom end. dyno'ed at 101.6bhp currently running 15 seconds dead over the quarter mile. car with engine ready to have fun nla car without engine £800...

so who fancies a go at building a car to a specification for a bit of tight and competitive drag racing ? a rough specification eligible cars- beetle ,ghia,type3Unmodified floor pan with beam or McPhersonstruts , with full working brakes . Unmodified shell , doors, boot and bonnet...

pulled the box apart this morning , and found the spider gears in the diff in pieces and I bit has pushed a hole into the cover plate , the rest of the transmission looks ok.

the cars engine was shaking badly at drag day , like a Hotpoint on spin with concrete blocks inside , PS don't try that ! pulled the motor Saturday and found both transmission mounts in several pieces , so we solid mounted the transmission , will see if its cured on 21st September.

A few folks have ask about the cost of using Elite Motors Dyno. They have a club rate as follows 1- 4 vehicles £50 each 5-10 vehicles £40 each 10 + vehicles £35 each this is for 3- 4 power runs and printout of results. if you want the dyno by the hour its £150/hour . they can be...

at bishops court run by http://www.facebook.com/shiftjunkies shift junkies btw check out there new photo heading. from there page... Right guys we are please to invite ye all to our very first OPEN DRAG DAY to launch our Drag Racing Orientated website,, yes this means ALL MAKES and MODELS of...

time to photo the dyno printouts from last Saturday, stick them up with a brief engine spec tetnasaurus. I don't have a sheet but it made 99.7hp and 120ftlbs 92mm bore x 69mm stroke 1835cc engle 120 camshaft heads stock 35.5mm inlet valves 32mm exhaust. twin weber 40IDF's

should we have a new forum sub section for drag racing / racing related items ?

http://www.youtube.com/watch?v=oXRKo4MYmCU&feature=youtu.be

rust free rear valences red one mint £80 grey one bottom edge need straightning £50 rust free sliding door for left hand drive from usa years ago when rust free was rust free. £250 bare opening side window in door £50 another the same needs a few small dents sorting but no rust...

http://carcultureni.com/ at bishops court on 7th july . talking to the organisers and its £10 in then another £10 to drag race. there is a show and shine that has a category for vintage VW so come a long show your car and watch the racing .

just finishing a 1776 long block. should get it bench tested this week fitted with counter weight 69mm crankshaft lightened 8 dowel flywheel mahle 90.5 piston and barrels scat c25 camshaft full flowed case with remote filter, suitable for beetle split or bay. valves fitted with heavy duty...

BCode 1600 single port engine, had a stripped oil pressure switch boss now fixed but i stripped the engine down and rebuilt using new seals gaskets etc . bench tested ok long block £400

used 77mm piston/barrel set and heads from a 1976 1200 in good condition £100 used 77mm piston/barrel set from 1966 1200 in good condition £40 2 x used 1200 heads low mileage part numbers 113 101 373 £75 2 x used 1500/1600 single port heads very low mileage part numbers 311 101 373A...

4 stud centerline wheels wanted , nothing else just centerlines to match my wheels so I can make up second set of race tyres. what you got ?

dates so far 17th march at bishops court http://sideways-racing.com/ 11th /12 may Ballykelly, Limavady . north west speed trials

just finished a van engine 1600 twin port . this was a remtech recon , i have stripped the engine and rebuilt it with new gaskets /seals /exhaust valves/ 009 distributor. the engine has tinware fanhousing and alternator fitted, just needs an exhaust and carburettor to complete. the...

selection of dividers / calipers - inside, outside and straight . 10 items in total. £20 or 25euro + £5 to post from armagh to all ireland.